Anubis3D company logo with stylized jackal head
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

The surface finish of a 3D printed part decides how it looks, how it feels, how easy it is to clean and sometimes whether it can be used at all. A selective laser sintering (SLS) nylon part comes out of the printer with a matte, slightly grainy surface, typically around Ra 10 to 15 µm, and every finishing option changes that texture, changes the colour, seals the surface or does some combination of the three.

This guide puts the finishes we offer on our SLS parts side by side: what each one does to roughness, appearance, dimensions, cost and lead time, and the applications where we would actually recommend it.

As printed surface
Around Ra 10 to 15 µm
Smoothest finish
Vapor smoothing
Roughness reduction
Up to about 70%
Finishing cost
Adds 10 to 20%

SLS Surface Finishes at a Glance

FinishWhat it doesSurface feelRelative costBest for
As printedMedia blasting removes loose powder, colour stays natural whiteMatte, slightly grainy, like very fine sandpaperIncludedFunctional prototypes, internal parts, jigs and fixtures
TumbledVibratory media wears down the peaks of the surfaceSmoother, close to eggshell, with softened edgesLowBatches of sturdy parts that need a nicer feel
DyedA heated dye bath colours the surface layerSame texture as printedLowColour coding, black cosmetic parts, hiding wear
Vapor smoothedA solvent vapour reflows and seals the outer surfaceSmooth, semi gloss, sealedHighestFood and beverage, washdown, fluid channels, customer facing parts
Painted or lacqueredAerosol or professional paint, or a clear lacquer coatMatte to gloss, depending on preparationMediumBrand colours, Pantone matches, UV and soiling protection

As Printed: The Baseline Finish

Every SLS part we ship is cleaned of unsintered powder by media blasting, and for a lot of parts that is where finishing stops. The result is a uniform matte surface in natural white, with the same texture on every face. Unlike filament printing, there are no visible tool paths, although gentle curves can show slight stepping between layers.

The trade-off is porosity. An as printed surface is slightly open, so it picks up dirt, oil and moisture over time and is harder to clean. Dimensions are not affected. For functional prototypes, internal brackets, fixtures and most robot tooling, the as printed finish is the right call because it costs nothing extra and adds no time.

Bead Blasting and Tumbling: Mechanical Smoothing

Mechanical finishes smooth the part by physically knocking down the peaks of the surface. A finer blast gives a more even, satin matte look. Tumbling, also called vibratory finishing, runs parts in a tub of media for a longer period and takes the surface close to an eggshell feel.

  • It only works on surfaces the media can reach, so deep internal channels stay as printed.
  • Sharp edges become rounded, and very small or thin features can be damaged, so keep walls above the minimums in our design guidelines for SLS.
  • Many parts are processed together, which makes tumbling an economical way to improve a whole batch.
  • A tumbled surface takes paint, coatings and dye well.

Dyeing: Colour Without Changing the Surface

SLS nylon is porous enough to take dye readily, which makes dyeing the simplest way to change the colour of a part. Black is by far the most common request, and other colours come from a standard range. Parts are immersed in a heated dye bath, and the colour goes a short way into the surface rather than sitting on top of it, so a light scratch does not immediately show white the way it would on paint.

Dyeing does not change dimensions or texture. If you want a deeper, more even colour, dyeing after vapor smoothing gives a noticeably richer result, and adding a clear lacquer over a dyed part improves UV protection for parts that live outdoors or near windows.

Vapor Smoothing: Sealed, Smooth and Washable

Vapor smoothing is the biggest change you can make to an SLS surface. We use the DyeMansion VaporFuse process, where a solvent vapour softens the outer layer of the part and lets it reflow before the solvent is fully extracted. Because it is a vapour, it reaches internal channels and undercuts that blasting and tumbling cannot.

  • Surface roughness can drop by up to around 70 percent, to a smooth semi gloss finish.
  • The surface is sealed against fluids, which makes parts easier to clean and less prone to bacterial build up.
  • Elongation at break improves, so parts become tougher.
  • Dimensional change is small, typically within about 0.4 percent.

It is not a polish. The overall shape of the surface is still there, just smoother and sealed. For food contact, the solvent used in the process complies with Regulation (EU) 10/2011 according to DyeMansion, and we cover that in more detail in our post on Vapor Fuse smoothing.

Macro view of raw grainy SLS nylon next to a smooth sealed vapor smoothed surface

Painting and Lacquer: Colour Matching and Protection

Paint is the route to an exact colour. Aerosol paints in matte, semi gloss and gloss come from standard stock, and professional painting gives you Pantone colour matching when a part has to match a brand or an existing product. A clear lacquer coat is the protective option: it improves wear resistance and surface hardness, helps with water tightness and reduces soiling.

Paint sits on the surface, so preparation decides the result. Tumbling or vapor smoothing first gives the cleanest paint finish, and because paint is a surface layer, a deep chip will show the base colour underneath.

Which Finish for Which Application

ApplicationRecommended finishWhy
Functional prototypeAs printedCheapest and fastest, and texture rarely matters at this stage
Robot gripper fingers and EOAT bodiesAs printed or dyed blackDurable, and black hides wear on parts that handle product all day
Food and beverage handlingVapor smoothedSealed, washable surface with an (EU) 10/2011 compliant smoothing process
Fluid or air channels and manifoldsVapor smoothedSeals the walls and smooths internal passages
Customer facing or consumer partVapor smoothed and dyed, or paintedThe best look and feel
Brand colour or Pantone matchPaintedDye colours are standard, paint can be matched
Large batch of small partsTumbledSmooths many parts at once at low cost
Outdoor or UV exposed partDyed with lacquer, or paintedBetter UV protection than an untreated surface

Most of our own end-of-arm tooling ships as printed or dyed black, because what matters on a gripper is how it performs, not how it looks.

Area Surface Gripper handling multiple box sizes in one pick pattern

How Finishing Affects Cost and Lead Time

The as printed finish is included in the part price. Tumbling and dyeing add a little, painting a bit more, and vapor smoothing the most, with finishing typically adding somewhere in the range of 5 to 15 percent of the print cost. Each step also adds time on top of our standard SLS lead time of 3 to 4 business days, so if a date is fixed, tell us up front.

The most useful thing you can give us is not a finish name but a requirement: what the part has to survive, whether it gets washed, whether a customer will see it. From that we can tell you whether a finish is worth paying for, and our post-processing options page goes into each process in more depth.

Where We Sit

We are Anubis 3D Industrial Solutions. We produce SLS nylon parts on six EOS printers at our facility in Mississauga, Ontario, and finish them with the options above, including vapor smoothing on DyeMansion VaporFuse. We also design and build end-of-arm tooling, so most of the parts we make are functional rather than decorative.

That colours our advice. In our experience, the majority of industrial parts need nothing beyond the standard finish, and when they do, the reason is usually cleaning or sealing rather than looks.

SLS Surface Finish Questions

What is the surface finish of an SLS part?

As printed, an SLS nylon part has a uniform matte, slightly grainy surface, typically around Ra 10 to 15 micrometres. It is natural white and slightly porous.

What is the smoothest finish for SLS parts?

Vapor smoothing gives the smoothest SLS finish. It reflows the outer surface with a solvent vapour, cutting roughness by up to around 70 percent and sealing the part, including internal channels.

Can SLS parts be dyed any colour?

SLS parts take dye well, and black is the most common choice. Dye colours come from a standard range, so for an exact brand colour or Pantone match, painting is the better option.

Does finishing change the dimensions of a part?

Dyeing does not change dimensions. Vapor smoothing typically keeps parts within about 0.4 percent. Tumbling and blasting remove a little material at edges and corners, so very fine features can soften.

Are vapor smoothed SLS parts food safe?

Vapor smoothing seals the surface and makes parts easier to clean, and the solvent used in the VaporFuse process complies with Regulation (EU) 10/2011 according to DyeMansion. The base material must also suit food contact, and EOS states that PA 2200 complies with EU Regulation 1935/2004.

Not Sure Which Finish You Need?

Tell us what the part has to survive and how it should look, and our team will recommend a finish with your quote.


Request a Quote

Tell us what you need and we’ll get back to you with a quote. Pick the one that fits your project.

Let us Stay Connected!

Enjoyed this article? Follow us for more insights, updates, and innovations:

Send Us a Message

This field is for validation purposes and should be left unchanged.
20mb limit. For files larger than that please call us for an FTP link.
Drop files here or
Accepted file types: jpg, png, pdf, stl, step, stp, iges, igs, xt, jpeg, Max. file size: 20 MB.